LI.BE S.p.A.

S.S. 10 - Località Fabbrica 46, 27040 Arena Po (Pv)
Italy

Telephone +39 0385 272419
Fax +39 0385 272478
info@li-be.com

Location

Hall map

METEC 2015 hall map (Hall 4): stand D38

Fairground map

METEC 2015 fairground map: Hall 4

Our products

Product category: Components, ancillary equipment

Back-Up Rolls - Yoke type track rollers full complement

For this series of bearings a special accuracy has been used in the choice of the raw materials and dimensions of the rolling elements as far as their profile and
selection are concerned.
Mechanical double protections are provided, composed of lamellar sheet and of metal sheet cover.
The axial guidance of the rollers is provided by the central spacers which act at the same time as a lubricant tank.
The outer ring can be cylindrical or rounded and of different hardness, according to customer’s requests.
Bearings of this series are individually checked in order to certify their dimensions according to their operating factors. If required LI-BE can supply a complete
set of pre-selected bearings to be mounted on the same machine bench.
Our aim is to obtain the best equal load distribution on the rollers in order to improve their functioning and to get a longer service life of the bearings.

More Less

Product category: Components, ancillary equipment

Back-Up Rolls - Yoke Type Track Rollers With Shaft

The yoke type track rollers of this series are normally recommended when the metal sheet to be leveled has a low thickness.
The rolling elements have sealed protections made of rubber rings type O-rings and of traditional sealing rings with lips.
If required LI-BE can supply a complete set of pre-selected bearings to be mounted on the same machine bench. The purpose is to obtain the best equal load
distribution on the rollers in order to improve their functioning and to get a longer service life of the bearings.
Bearings of this series are individually checked in order to certify their dimensions according to their operating factors.

More Less

Product category: Components, ancillary equipment

Hot Rolled Steel Section With 'C' Shape

Hot rolled steel sections meet most of the technical requirements that arise when designing equipment for goods handling.

More Less

Product category: Components, ancillary equipment

Combined Bearings For Steel Sections

The combined bearings are manufactured according to the Unified Parameters which govern a correct execution of rolling bearings.
This series can be supplied both with steel shield and they can therefore be relubricated and in the sealed performance.The outer rings are normally scheduled
in correct convex performance to counteract the inevitable geometrical errors originating from the coupling with the guideways in which they roll.
Bearings are greased at source with grade “3” lithium base grease.
For special performances, as the use of these bearings at high temperatures, please inquire our Engineering Office.

More Less

Product category: Components, ancillary equipment

Back-Up Rolls - Customized Solutions

CUSTOMIZED BACK-UP ROLLS engineered according to the most recent simulation technology. Best load performance and lifetime guaranteed.

Entirely designed and manufactured in our factory in Italy to ensure a superior quality product

More Less

Product category: Components, ancillary equipment

Combined Bearings For Heavy Loads Adjustable From Outside

They are designed especially to be used on equipments with high loading capacity and guarantee high reliability and resistance to stress.
The dimensions indicated in the table are suitable for equipments with loading capacity from 16 to 42 tons.
The space-saving design of these bearings allows a particularly compact construction of the masts, i.e. a better visibility.
Bearings of this series are adjustable only on the thrust side, by means of an eccentric stud adjustable from outside.
The stud provides the recovery of the clearances arising from the heavy applications of the lift trucks.
The rolling elements are protected by means of rings in plastic material with double lip and with a metallic screen to prevent damages coming from
mechanical stress.
These combined bearings are long life lubricated with Lithium base grease of consistency class “3” and therefore they do not require re-lubrication.

More Less

Product category: Components, ancillary equipment

Rollers For Coils Conveyors Chains (MRYM Execution)

More Less

Product category: Components, ancillary equipment

Rolling Mill Bearings, SIX rows with CYLIDRICAL bore

Cylindrical roller bearings with four or more rows of rollers are used almost exclusively for rolling mills. They have lower friction than other roller bearings and can be successfully used where high speed operation is called for. The low cross-sectional height of cylindrical roller bearing means that the roll necks can have large diameter in relation to the roll itself. Cylindrical roller bearing with more than four rows of rollers and cages are used primarily for small cold rolling mills and for flat products where the rolling forces are considerable and rolling speed high. Multi-row bearings are produced for roll neck diameters of up to approximately 220mm. The outer ring is without flanges. Limited axial displacement of the shaft with respect to the housing can therefore be accomodated by the bearing.

More Less

Product category: Components, ancillary equipment

Rolling Mill Bearings, Four Rows With CYLINDRICAL Bore

Cylindrical roller bearing with four or more rows of rollers are used almost exclusively for rolling mills. They have lower friction than other roller bearings and can be successfully used where hight speed operation is called for. The low cross-sectional height of cylindrical roller bearings means that the roll necks can have large diameter in relation to the roll itself. In four rows cylindrical roller bearings, the rollers are guided between integral or not-integral flanges on the outer ring. The inner ring is without flanges; axial displacement of the shaft with respect to the housing can therefore be accomodated by the bearing within certain limits. Depending on the application, four rows cylindrical roller bearings can be supplied with a cylindrical bore or tapered bore. The inner or outer ring may be in one piece ore in more than one piece.

More Less

Product category: Components, ancillary equipment

Rolling Mill Bearings, Four Rows With TAPERED Bore

Cylindrical roller bearing with four or more rows of rollers are used almost exclusively for rolling mills. They have lower friction than other roller bearings and can be successfully used where hight speed operation is called for. The low cross-sectional height of cylindrical roller bearings means that the roll necks can have large diameter in relation to the roll itself. In four rows cylindrical roller bearings, the rollers are guided between integral or not-integral flanges on the outer ring. The inner ring is without flanges; axial displacement of the shaft with respect to the housing can therefore be accomodated by the bearing within certain limits. Depending on the application, four rows cylindrical roller bearings can be supplied with a cylindrical bore or tapered bore. The inner or outer ring may be in one piece ore in more than one piece.

More Less

About us

Company details

https://www.youtube.com/user/libebearings

---------------------------------------------------------------------------------

Founded in 1984, LI-BE produces special bearings, by dimension and execution, for different industrial applications.

The range of production includes bearings, rollers and complementary articles (slides and plates) used in the sector of metallurgical machinery, internal goods handling, painting machinery, power transmission units, rotating tables for tool machines, etc.

LI-BE has always been synonymous with special bearings and is the holder of some international patents. For this reason the company uses a team of experts who are capable of providing solutions and projects which are suited to customers' specific requirements.

The company activity has produced constant growth, enabling it to employ avant-garde production systems combined with modern control equipment necessary to carry out rigid and precise testing operations during each work cycle.

LI-BE boasts a strong presence in both national and international markets.

Notwithstanding its hard-won position as market leader and aware of the rugged competition existing in its industry, LI-BE has never taken its attention off the niche market which are open to those companies that take flexibility, readiness, experience and reliability their strong points, as LI-BE does.

The company has enjoyed various periods of investment enabling it to produce high precision and high-quality bearings.

More Less